= tellstick.conf = The file {{{/etc/tellstick.conf}}} is the file where all devices used by TellStick is configured under Linux. Each device is configured in its own block with the parameter as name/value-pairs: {{{ device { foo = "bar" } }}} A device has at least four values and another block names {{{parameters}}}. A typical device can look like this: {{{ device { id = 1 name = "Device 1" protocol = "arctech" model = "codeswitch" parameters { house = "A" unit = "1" } } }}} id:: This is a number and must be unique for each device. name:: A name for easy identification of the device. protocol:: This is the protocol the device uses. More on the different protocols later down. model:: The parameter model is only used by some protocols where there exists different types of devices using the same protocol. This can be dimmers versus non-dimmers, codeswitch versus selflearning etc. parameters:: This block depends on the protocol specified and is explained under each protocol. == Protocols == === arctech === This protocol is used by a lot of devices. Some of them includes: * Byebye Standby * Chacon * CoCo Technologies * HomeEasy * Intertechno * Kappa * KlikAanKlikUit * Nexa * Proove * Rusta It has four different models: codeswitch:: This types of devices uses dials on the receiver and remote to address them. The parameter {{{house}}} can be A to P and the {{{unit}}} 1 to 16. A typical parameters-block can look like: {{{ parameters { house = "A" unit = "1" } }}} bell:: This is bells of the codeswitch type. It only uses {{{house}}} and just as model {{{codeswitch}}} it is A to P. Example: {{{ parameters { house = "C" } }}} selflearning-switch:: Requires TellStick batch >= 5, TellStick Duo or TellStick Net[[BR]] The newer ones where the code is learned by the remote/TellStick. Instead of housecodes A to P this is now 1 to 67108863. The unitcode is still 1 to 16. Example: {{{ parameters { house = "953934" unit = "1" } }}} selflearning-dimmer:: Requires TellStick batch >= 5, TellStick Duo or TellStick Net[[BR]] This is the same as {{{selflearning-switch}}} only these devices supports dimming-commands === brateck === Requires TellStick batch >= 5, TellStick Duo (sending only) or TellStick Net (sending only)[[BR]] This protocol is used by some projector screens. Example: * Roxcore The only parameter used in this protocol is {{{house}}}. The code is 8 tri-state values soldered into the pcb. The state can be "1", "0" or "-". A real world example can be found here: http://www.telldus.se/forum/viewtopic.php?t=416 Example: {{{ parameters { house = "101-1011" } }}} === everflourish === Requires TellStick batch >= 5, TellStick Duo or TellStick Net[[BR]] Added to telldus-core in 2.0.2. This is the selflearning protocol. For the codeswitch, take a look at {{{risingsun}}}. Brands: * GAO The protocol uses {{{house}}} (0 to 16383) and {{{unit}}} (1 to 4). Example: {{{ parameters { house = "117" unit = "2" } }}} === fuhaote === Requires TellStick batch >= 5, TellStick Duo or TellStick Net[[BR]] Added to telldus-core in 2.0.3. The configuration of these devices is very similar to {{{sartano}}} but they are not compatible with each other. Brands: * HQ * Rusta It uses the parameter {{{code}}} and consists of ten ones and zeros. Example: {{{ parameters { code = "0010010100" } }}} === hasta === TellStick Duo and TellStick Net can only send, not receive this protocol[[BR]] Blinds[[BR]] Uses {{{house}}} (1 to 65536) and {{{unit}}} (1 to 15). Example: {{{ parameters { house = "1" unit = "1" } }}} === ikea === These receivers is not sold by Ikea anymore. There is both dimmers and non dimmers. One thing that differs this protocol against all other is that it can control up to ten receivers with just one device. It uses the parameters {{{system}}}, {{{units}}} and {{{fade}}}: {{{system}}} can be 1 to 16. {{{units}}} is a comma-separeted list of receivers to address (1 to 10). {{{fade}}} is either {{{true}}} or {{{false}}} and tells a dimmer if is should fade smooth or instand between values. Example: {{{ parameters { system = "5" units = "2,6" fade = "true" } }}} === risingsun === TellStick Duo and TellStick Net can only send, not receive this protocol[[BR]] Often small codeswitch receivers. Known brands: * Conrad (selflearning) * GAO (codeswitch) * Kjell & Company (codeswitch) * Otio (selflearning) Two models, codeswitch or selflearning: codeswitch:: Uses {{{house}}} (1 to 4) and {{{unit}}} (1 to 4). Example: {{{ parameters { house = "1" unit = "1" } }}} selflearning:: Uses {{{house}}} (1 to 33554432) and {{{unit}}} (1 to 16). Example: {{{ parameters { house = "5679" unit = "1" } }}} === sartano === This is a very common protocol used by a lot of receivers. It has 10 dip-switches to configure the adress-code. Brands: * Sartano * Alpha * Brennenstuhl * Elro It uses the parameter {{{code}}} and consists of ten ones and zeros. Example: {{{ parameters { code = "0010010100" } }}} === silvanchip === TellStick Duo and TellStick Net can only send, not receive this protocol[[BR]] Brands: * Ecosavers * KingPin - KP100 Two models, ecosavers and kp100 ecosavers:: Uses {{{house}}} (1 to 1048575) and {{{unit}}} (1 to 4). Example: {{{ parameters { house = "1" unit = "1" } }}} kp100:: Uses {{{house}}} (1 to 1048575). Example: {{{ parameters { house = "1" } }}} === upm === TellStick Duo and TellStick Net can only send, not receive this protocol[[BR]] Uses parameters {{{house}}} (0 to 4095) and {{{code}}} (1 to 4). Each receiver can only remember one code at a time so using both a normal remote and TellStick is not possible. Example: {{{ parameters { house = "123" unit = "1" } }}} === waveman === Very similar to arctech/codeswitch but the protocol differs just slightly. Brands: * Waveman Example: {{{ parameters { house = "A" unit = "1" } }}} === x10 === Requires TellStick batch >= 9, TellStick Duo or TellStick Net[[BR]] This protocol uses the same configuration as arctech/codeswitch. Example: {{{ parameters { house = "A" unit = "1" } }}} === yidong === Added to telldus-core in 2.0.4. Brands: * Goobay Uses {{{unit}}} (1 to 4). Example: {{{ parameters { unit = "1" } }}}